
74.95 £
Four piece cutter set for use by kitchen fitters comprising two worktop cutters, one biscuit jointer and one laminate trimmer. Can be used in natural timbers, particle board and fibreboard. The biscuit jointer is supplied with three bearings to...

35.95 £
Neatly cuts grooves on doors or frames to accept Intumescent Strip. For use with seals of 10mm width and 4mm thickness. By using alternative ball bearing diameters, other seal thicknesses can be introduced. For either frame or door applicati...

42.95 £
Case is supplied complete with metal and foam support pieces for the router and space is sufficient for storage of accessories such as side fence, fine height adjuster, guide bushes and dust hood. Case has space for storage of fourteen cutters.

25.95 £
Neatly cuts grooves on doors or frames to accept Intumescent Strip. By using alternative ball bearing diameters, other seal thicknesses can be introduced. For either frame or door applications, with standard or Smokeseal Intumescent Strip. A...

48.95 £
For use with commercial dovetailing and stair-housing jigs. The cutter will produce sliding and lapped dovetails, through dovetails and end on dovetails. Purpose made for stair housing jigs. Left hand. Dimensions : Diameter=16 mm

7.95 £
Inner plate for the T10 router. Please note that prices in the Trend Catalogue download, if shown below, may differ to the website prices, as those listed in the Catalogue are Trend List Prices excluding VAT....

36.95 £
A cutter to create a knuckle joint for tabletop support, for use on natural timber. For use with 19mm thick material. Dimensions : Diameter=28.5 mm Cutting Radius 1 : 9.5 mm Shank Diameter : 1/4 inch Please note that prices in ...

54.95 £
This cutter will produce an effective 90 degrees corner joint and can be used for jointing lengths of timber together. For inverted use only. Machining of this joint is carried out by routing one piece with the inside face on the table. The...

6.49 £
17mm A/F single open ended spanner. Please note that prices in the Trend Catalogue download, if shown below, may differ to the website prices, as those listed in the Catalogue are Trend List Prices excluding VAT....

8.49 £
Optional 4 inch template for the Butt Hinge Template. Please note that prices in the Trend Catalogue download, if shown below, may differ to the website prices, as those listed in the Catalogue are Trend List Prices excluding VAT....

9.95 £
Two fluted Tungsten Carbide Tipped straight cutters. Suitable for a wide range of applications such as engraving, grooving, rebating and shallow mortising. Use on softwoods, hardwoods, MDF, plywood and chipboard. Has a bottom cut feature....

10.95 £
Lighter duty mitre fence for use with router tables, saw benches and band saws. Moulded plastic protractor body. Angled at -60 degrees, 0 degrees and +60 degrees, with the scale marked at 5 degree pitch. Supplied with a beech spelch block along wi...

16.95 £
Pair of 110v carbon brushes for the T10 & T11 router. Please note that prices in the Trend Catalogue download, if shown below, may differ to the website prices, as those listed in the Catalogue are Trend List Prices excluding VAT....

7.95 £
Replacement bearing for router cutter. Always check the tightness of the fixing screw before using the cutter. Ball bearings should be wiped clean, not dipped in solvent. Prevent resin build-up by cleaning with wire brush. Dimensions : ...

45.95 £
Use for producing mortar grooves and for bevelling applications. Dimensions : Diameter : 38mm Cutting Length 1 : 27mm Cutting Length 2 : 25.5mm Angle : 60 degrees Shank Diameter : 1/2 inch Please note that prices in the Trend Cata...

18.95 £
Tungsten Carbide tips ensure long life and the storage case provides a safe place to store the bits when they are not being used. Router Bit sets with different cutter shapes which enable the creation of a variety of profiles, grooves ...

56.95 £
Tungsten Carbide tips ensure long life and the storage case provides a safe place to store the bits when they are not being used. Router Bit sets with different cutter shapes which enable the creation of a variety of profiles, grooves ...

16.95 £
1/4 and 1/2 shank extra long router bits with TCT heads especially for use with extra thickness laminate used by kitchen fitters. Supplied with hexagon key. Display packed in storage case. Contents : •   1 x Flush ...

51.95 £
A quarter ellipse cutter for architraves and mould finishes. For stationary machines - 12000 RPM recommended speed. Dimensions : Diameter=69.2 mm Cutting Radius 1 : 44 mm Shank Diameter : 1/2 inch Please note that prices in the...

14.95 £
Two fluted Solid Carbide insert straight cutters. Suitable for a wide range of applications such as engraving, grooving, rebating and shallow mortising. Use on softwoods, hardwoods, MDF, plywood and chipboard. Has a bottom cut feature.