Neatly cuts grooves on doors or frames to accept Intumescent Strip. For use with seals of 20mm width and 4mm thickness. By using alternative ball bearing diameters, other seal thicknesses can be introduced. For either frame or door applicati...

For coves and part of a rule joint. Two flute. Dimensions : Diameter : 32mm Cutting Length : 31.7mm Cutting Radius : 16mm Shank Diameter : 1/2 inch Please note that prices in the Trend Catalogue download, if shown below, may ...

Collets designed to fit Dewalt routers. Collet to fit the following DeWalt Routers. Models DW613 DW620 DW621K Size. 1/4in. ...

Collets designed to fit Dewalt routers. 8 mm Collet to fit DEW625EK Router. ...

The manufacturing specification for Faithfull router bit cutters ensures that they are suitable for use by all professional tradesmen, craftsmen and conscientious DIY enthusiasts. Every Faithfull router cutter tip is made from tungsten carbi...

Four piece router bit set for use with kitchen worktop jigs. Tungsten carbide bits suitable for all routers with 1/2in collet. Set contains : 1 Straight Cutter : 12.7mm x 60mm x 1/2in shank 2 Straight Cutters : 12.7mm x 50mm x 1/2i...

This cove style cutter with two flutes, give radiused grooves for decorative panel finishes and board edges. For deep channels, take a series of passes. Dimensions : Diameter=3/4 inch Diameter=19.1 mm Cutting Length : 1/2 inch Cut...

A two piece cutter set to create a traditional frame and panelled door using a router in a table. The cutters have extra long shanks and can be used in natural timber. Supplied in a wooden box with instructions The panel raiser is for fixed ...

Two fluted Tungsten Carbide Tipped straight cutters. Suitable for a wide range of applications such as engraving, grooving, rebating and shallow mortising. Use on softwoods, hardwoods, MDF, plywood and chipboard. Has a bottom cut feature....

Replacement alloy wing for the HM/SHEAR. Please note that prices in the Trend Catalogue download, if shown below, may differ to the website prices, as those listed in the Catalogue are Trend List Prices excluding VAT....

Trend F'Plate Template 17 44.6X171 Round Face plate template for the LOCK/JIG. Dimensions : 44.6 X 171 Round Please note that prices in the Trend Catalogue download, if shown below, may differ to the website prices, as those li...

HSS drill for use with the BL/JIG/95. Dimensions : Diameter 3/8 inch Please note that prices in the Trend Catalogue download, if shown below, may differ to the website prices, as those listed in the Catalogue are Trend List Prices exc...

This cutter is self-guiding & can be used to produce rebates, lap joints, tongues & rebated corners. Dimensions : Diameter=31.8 mm Cutting Length : 15.9 mm Bearing Diameter : 9.5 & 12.7 mm Shank Diameter : 1/2 inch Please note t...

For use with commercial dovetailing and stair-housing jigs. The cutter will produce sliding and lapped dovetails, through dovetails and end on dovetails. Purpose made for stair housing jigs. Left hand. Dimensions : Diameter=25 mm

Two fluted Tungsten Carbide Tipped straight cutters. Suitable for a wide range of applications such as engraving, grooving, rebating and shallow mortising. Use on softwoods, hardwoods, MDF, plywood and chipboard. Has a bottom cut feature....

Replacement bearing for router cutter. Always check the tightness of the fixing screw before using the cutter. Ball bearings should be wiped clean, not dipped in solvent. Prevent resin build-up by cleaning with wire brush. Dimensions : ...

For use with commercial dovetailing and stair-housing jigs. The cutter will produce sliding and lapped dovetails, through dovetails and end on dovetails. Purpose made for stair housing jigs. Dimensions : Diameter=25 mm Angle : 95 de...

Carbon bush for the T10 router. Please note that prices in the Trend Catalogue download, if shown below, may differ to the website prices, as those listed in the Catalogue are Trend List Prices excluding VAT....

A six piece pack for use by kitchen fitters. The pack comprises of one worktop cutter C153DX1/2TC, one biscuit jointer C152X1/2TC, 3 x metal panel connectors and a bag of ten No 20 biscuits. Cutters are tungsten carbide tipped with a teflon coatin...

Replacement phenolic slider for the T11. Please note that prices in the Trend Catalogue download, if shown below, may differ to the website prices, as those listed in the Catalogue are Trend List Prices excluding VAT....