Replacement bearing for router cutter. Always check the tightness of the fixing screw before using the cutter. Ball bearings should be wiped clean, not dipped in solvent. Prevent resin build-up by cleaning with wire brush. Dimensions : ...

Right handle for the T10 router. Please note that prices in the Trend Catalogue download, if shown below, may differ to the website prices, as those listed in the Catalogue are Trend List Prices excluding VAT....

For stationary machines or portable routers mounted in a table. Fixed head use, maximum 18000 rpm. Dimensions : Diameter=50 mm Cutting Radius 1 : 12 mm Shank Diameter : 1/2 inch Please note that prices in the Trend Catalogue do...

Please note. This tool should not be resharpened. Thickness Min. 8mm - Max. 12mm. For stationary machines at 24000 RPM. Dimensions : Diameter=42 mm Cutting Length 1 : 12 mm Angle : 45 degrees Shank Diameter : 1/4 inch Plea...

Two fluted tungsten carbide weatherseal groover for use on natural timbers and manmade boards. The cutter is Teflon cutted to reduce resin build up. Neatly cuts grooves on doors or frames to accept a weattherseal. Dimensions : Diameter=36...

Ideal for engraving and veining work. Use on timber and man made boards. Dimensions : Diameter=1/2 inch Diameter=12.7 mm Cutting Length : 11 mm Overall Length : 45 mm Angle : 45 degrees Shank Diameter : 1/4 inch Please n...

Flat Roman Ogee, for raised panelling or edge moulding. Used for decorative capping on hand rails. For stationary machines - 18000 RPM recommended speed. Dimensions : Diameter=50 mm Cutting Length 1 : 6.5 Cutting Length 2 : 11.5 mm C...

Two fluted Tungsten Carbide Tipped straight cutters. Suitable for a wide range of applications such as engraving, grooving, rebating and shallow mortising. Use on softwoods, hardwoods, MDF, plywood and chipboard. Has a bottom cut feature....

A bearing guided round over & ovolo router cutter supplied with three ball bearings to give a rounding over and two sizes of step ovolo mould on timber. Round over effect with largest bearing. Ovolo with 1.6mm (1/16+) step/quirk using 1/2+ bearing...

Two fluted Tungsten Carbide Tipped straight cutters. Suitable for a wide range of applications such as engraving, grooving, rebating and shallow mortising. Use on softwoods, hardwoods, MDF, plywood and chipboard. Has a bottom cut feature....

Two fluted Solid Carbide insert straight cutters. Suitable for a wide range of applications such as engraving, grooving, rebating and shallow mortising. Use on softwoods, hardwoods, MDF, plywood and chipboard. Has a bottom cut feature.

A precision made laser cut zinc plated steel template comb for the CDJ300. A half blind 8mm box joint. Dimensions : Material thickness 12mm to 30mm. Material width up to 305mm. Box Joint Min. 8mm Max. 15mm Please note t...

A precision made laser cut zinc plated steel template comb for the CDJ600. A 1/2 inch through dovetail template. Dimensions : Material thickness 12mm to 30mm. Material width up to 610mm. Through dovetail Min. 8mm Max.17mm

A range of professional range cutters for use with the DC400 dovetailing centres. The set comprises of five dovetail cutters and two 8mm straight cutters. Dimensions : Comprises of a 7 degree, 9 degree, 11 degree, 14 degree & 20 degree dove...

Use for producing mortar grooves and for bevelling applications. Dimensions : Diameter : 38mm Cutting Length 1 : 27mm Cutting Length 2 : 25.5mm Angle : 60 degrees Shank Diameter : 3/8 inch Please note that prices in the Trend Cata...

This cutter will produce an effective 90 degrees corner joint and can be used for jointing lengths of timber together. For inverted use only. Machining of this joint is carried out by routing one piece with the inside face on the table. The...

This specially designed machine bits has a new form of scriber to allow use at higher speeds. For recessing circular hinges. For accurate repetitive routing, a template and guide bush fitted to the router base should be used. Use between 100...

This machine bit is designed for recessing circular concealed hinges. The shank has a flat for securing and a grub screw for height adjustment. Use at recommended speeds of 10000RPM. Dimensions : Diameter : 15mm Overall Length : 57mm

For coves and part of a rule joint. Single flute. Dimensions : Diameter : 10mm Cutting Length : 18mm Cutting Radius : 5mm Shank Diameter : 8mm Please note that prices in the Trend Catalogue download, if shown below, may diffe...

Small sized panelling cutter. Ideal for veining and fluting applications. Dimensions : Diameter : 9.5mm Cutting Length : 7.5mm Cutting Radius : 4.8mm Shank Diameter : 1/4 inch Please note that prices in the Trend Catalogue downlo...