A seven piece template set that allows elliptical picture frames and plaques to be routed. Templates are made of 8mm thick clear Acrylic. Picture frame templates Frame to suit 7+ x 9+ picture Frame to suit 5+ x 7+ picture Frame to suit ...

For trimming and bevelling timber, lippings and plastic laminate edges or any shaping applications. Self-guiding trimmer with bearings mounted on end of cutter. For trimming plastic or plywood overlay. For copy profiling, use the bearing t...

A five piece pack for use by kitchen fitters. The pack comprises of five worktop cutter C153DX1/2TC. Cutters are tungsten carbide tipped with a teflon coating and can be used in natural timbers, particle board and fibreboard. Please note th...

A routing template that allows a router to rout out a hinge recess on a door and frame. Magnets in template frame to hold the metal templates. Cuts rounded corners which can be removed with a corner chisel or chisel. Dimensions : For 7...

A large ogee panel mould cutter for traditional panelled doors. Suitable for use with Ref. PSC/2X1/2TC. For stationary machines or portable routers mounted in a table at 12000 RPM recommended speed. Dimensions : Diameter : 85.7mm Cuttin...

ERA latch template for the LOCK/JIG. Please note that prices in the Trend Catalogue download, if shown below, may differ to the website prices, as those listed in the Catalogue are Trend List Prices excluding VAT....

One flute. Eccentric single flute cutter. Cutter is chosen for fast free cutting, when cutting speed takes preference over finish. Must not be used in eccentric chucks. This cutter has a Solid Carbide insert rather than brazed tip. Han...

Replacement bearing for router cutter. Always check the tightness of the fixing screw before using the cutter. Ball bearings should be wiped clean, not dipped in solvent. Prevent resin build-up by cleaning with wire brush. Dimensions : ...

One flute. Eccentric single flute cutter. Cutter is chosen for fast free cutting, when cutting speed takes preference over finish. Must not be used in eccentric chucks. Dimensions : Diameter : 1/4 inch Diameter : 6.3mm Cutting L...

Self-guiding triple flute cutter. Extra fine trimming and longer life. For trimming of laminate or plywood overlay. Dimensions : Diameter=12.7 mm Cutting Length : 25 mm Angle : 90 degrees Shank Diameter : 1/4 inch Please...

Tungsten Carbide tips ensure long life and the storage case provides a safe place to store the bits when they are not being used. Router Bit sets with different cutter shapes which enable the creation of a variety of profiles, grooves ...

The quick release kit for the T11 router comprising of three sets of cams, bolts and fixings. Please note that prices in the Trend Catalogue download, if shown below, may differ to the website prices, as those listed in the Catalogue are Trend...

TCT for abrasive materials such as chipboard, MDF, plywood and certain hardwoods. Two flutes for clean finish. Suitable for plunge routers. Dimensions : Diameter : 7.9mm Cutting Length : 26mm Shank Diameter : 8mm Please note...

TCT for abrasive materials such as chipboard, MDF, plywood and certain hardwoods. Two flutes for clean finish. Suitable for plunge routers. Dimensions : Diameter : 8mm Cutting Length : 26mm Shank Diameter : 1/4 inch Please n...

One flute. Eccentric single flute cutter. Cutter is chosen for fast free cutting, when cutting speed takes preference over finish. The depth of cut should be a maximum of 1.0mm per pass. Must not be used in eccentric chucks. This cutte...

TCT for abrasive materials such as chipboard, MDF, plywood and certain hardwoods. Two flutes for clean finish. Suitable for plunge routers. Dimensions : Diameter : 8mm Cutting Length : 26mm Shank Diameter : 8mm Please note t...

Two flute tungsten carbide tipped dovetail cutter for use with the DC400 dovetailing centres. Dimensions : Diameter : 11.3mm Cutting Length : 14mm Angle : 11degrees Shank Diameter : 8mm Shank Length=45mm Please note that price...

Two flute tungsten carbide tipped dovetail cutter for use with the DC400 dovetailing centres. Dimensions : Diameter : 11.3mm Cutting Length : 14mm Angle : 11 degrees Shank Diameter : 1/4 inch Shank Length=45mm Please note that...

A precision made laser cut zinc plated steel template comb for the CDJ300. A 32mm dowel template. Dimensions : Material thickness 12mm to 30mm. Material width up to 305mm. Dowelling 32mm centres Max. 25mm Please note that ...

A precision made laser cut zinc plated steel template comb for the CDJ600. A half blind 1/2 inch box joint. Dimensions : Material thickness 12mm to 30mm. Material width up to 610mm. Box Joint Min. 8mm Max. 20mm Please n...