Has 2 lips, 2spurs and a centre brad point. Flutings are backed-off to give a radial relief and assist chip clearance. This drill is used mainly for drilling cross grained timber and particle board. Used in all branches of industry when clea...

This lip and spur dowel drill features Solid Carbide cutting tips, for continuous drilling of tear free dowel holes. Shank has one flat for positive holding. A threaded grub screw in the shank end allows for correct setting for a bank of drills...

This lip and spur dowel drill features Solid Carbide cutting tips, for continuous drilling of tear free dowel holes. Shank has one flat for positive holding. A threaded grub screw in the shank end allows for correct setting for a bank of drills...

This lip and spur dowel drill features Solid Carbide cutting tips, for continuous drilling of tear free dowel holes. Shank has one flat for positive holding. A threaded grub screw in the shank end allows for correct setting for a bank of drills...

This machine bit is typically used by kitchen furniture manufacturers for recessing circular hinges. Without scribers are for laminate covered boards. Dimensions : Diameter : 15mm Overall Length : 60mm Shank Diameter : 3/8 inch ...

This 60 degree taper multi-boring drill is ideal for end grain and through hole drilling applications. Reduces the likelihood of +break out+ to a minimum. Drill has a Solid Carbide cutting tip. Shank has one flat for positive holding. A t...

This 60 degree taper multi-boring drill is ideal for end grain and through hole drilling applications. Reduces the likelihood of +break out+ to a minimum. Drill has a Solid Carbide cutting tip. Shank has one flat for positive holding. A t...

This 60 degree taper multi-boring drill is ideal for end grain and through hole drilling applications. Reduces the likelihood of +break out+ to a minimum. Drill has a Solid Carbide cutting tip. Shank has one flat for positive holding. A t...

This adaptor is produced with a 10mm aperture. Will accept Ref. 4109, 4119, 4507, 1009, 1109 and 1209 drilling tools. The type of threaded shank may vary depending on the manufacturer of the multi-boring machine. Dimensions : Diameter...

This adaptor is produced with a 10mm aperture. Will accept Ref. 4109, 4119, 4507, 1009, 1109 and 1209 drilling tools. The type of threaded shank may vary depending on the manufacturer of the multi-boring machine. Dimensions : Diameter...

This countersink is produced from the best grade carbon steel, leaves a clean cut finish by virtue of their multi-tooth deep ground gullets. For use with fast spiral drills. Fits metric drills from 3mm to 12mm inclusive. Drill bit not includ...

This countersink is produced from the best grade carbon steel, leaves a clean cut finish by virtue of their multi-tooth deep ground gullets. For use with fast spiral drills. Fits metric drills from 3mm to 12mm inclusive. Drill bit not includ...

This countersink is produced from the best grade carbon steel, leaves a clean cut finish by virtue of their multi-tooth deep ground gullets. For use with fast spiral drills. Fits metric drills from 3mm to 12mm inclusive. Drill bit not includ...

Designed to drill and countersink simultaneously, a wide variety of materials. Supplied complete with HSS twist drill. Fully adjustable, a hex key is supplied. When setting-up, ensure flutes of drill are aligned with flute of counterbore.

Designed to drill and countersink simultaneously, a wide variety of materials. Supplied complete with HSS twist drill. Fully adjustable, a hex key is supplied. When setting-up, ensure flutes of drill are aligned with flute of counterbore.

Designed to drill and countersink simultaneously, a wide variety of materials. Supplied complete with HSS twist drill. Fully adjustable, a hex key is supplied. When setting-up, ensure flutes of drill are aligned with flute of counterbore.

Designed to drill and countersink simultaneously, a wide variety of materials. Supplied complete with HSS twist drill. Fully adjustable, a hex key is supplied. Used for plywood, particle boards and plastics (abrasive). When setting-up, en...

Designed to drill and countersink simultaneously, a wide variety of materials. Supplied complete with HSS twist drill. Fully adjustable, a hex key is supplied. When setting-up, ensure flutes of drill are aligned with flute of counterbore.

Made from Carbon steel and precision machined. Has a spiral point, single flute. Ideal for quick, clean deep holes. Must only be used with torque control drills to prevent wrist injury. Dimensions : Diameter : 10mm Overall Length : 155mm...

Made from Carbon steel and precision machined. Has a spiral point, single flute. Ideal for quick, clean deep holes. Must only be used with torque control drills to prevent wrist injury. Dimensions : Diameter : 13mm Overall Length : 155mm...