
8.49 £
Used to reduce the collet size to take cutters with smaller shanks. Should only be used as a stop-gap, as the correct size collet is recommended. Should not be used for extensive periods or heavy work. Dimensions : Shank ID - 6mm Collet O...

31.49 £
The collet is a one-piece multi-slit design to provide maximum grip on to the surface of the cutter's shank. Dimensions : Precision multi-slit one piece 3mm collet Please note that prices in the Trend Catalogue download, if shown belo...

10.85 £
Made from reinforced plastic and have a steel stud. Dimensions : Size= M8x36mm Quantity= 10 Please note that prices in the Trend Catalogue download, if shown below, may differ to the website prices, as those listed in the Catalogue...

8.49 £
Made from reinforced plastic and have a steel insert. Dimensions : Size= Male M6x30mm Quantity= 4 Please note that prices in the Trend Catalogue download, if shown below, may differ to the website prices, as those listed in the Cat...

11.49 £
Ideal for jig-making applications where temporary fixing is required. The tape can be removed from the material by rolling off with thumb. Material must be clean and free of dust for best results. Down pressure onto the materials being joine...

28.49 £
1/4 inch collet capacity. Dimensions : Atlas Copco (AEG) OFSE2000, Freud FT2000E, Casals FT2000VCE Please note that prices in the Trend Catalogue download, if shown below, may differ to the website prices, as those listed in the Cat...

31.49 £
Round sub-base can be used as a guide itself. Recessed to accept Trend Guide Bushes. Supplied with 1/4 inch and 1/2 inch shank line up pins Ensures concentricity of cutter and guide bush. Ensures accurate work is achieved. Supplied ...

31.37 £
Large rectangular shape to increase surface area support. Recessed to accept Trend Guide Bushes. Supplied with line up 10mm guide bush Ref GB10. Supplied with 1/4 inch and 1/2 inch shank line up pin. Ensures concentricity of cutter an...

8.49 £
Guide bush guides the router when using a template. Fits directly to Trend T3,T5,T9,T10 and T11, and some other light duty routers. Will fit other makes when used with GB/5, GB/PLATE or UNIBASE Sub-base. Dimensions : Outside diameter...

9.49 £
Guide bush guides the router when using a template. Fits directly to Trend T3,T5,T9,T10 and T11, and some other light duty routers. Will fit other makes when used with GB/5, GB/PLATE or UNIBASE Sub-base. Dimensions : Outside diameter...

15.49 £
Guide bush guides the router when using a template. Dimensions : Outside diameter - 50mm Please note that prices in the Trend Catalogue download, if shown below, may differ to the website prices, as those listed in the Catalogue are ...

15.49 £
Guide bush guides the router when using a template. Dimensions : Outside diameter - 70mm Please note that prices in the Trend Catalogue download, if shown below, may differ to the website prices, as those listed in the Catalogue are ...

34.61 £
When setting up jigs, templates and routing devices, it often becomes necessary to temporarily fasten parts together. For this purpose, Trend offer threaded inserts for fixings in plastics, woods, man-made boards and fibre board e.g. MDF. Threa...

8.49 £
Made from re-inforced plastic, with a plated steel studding. Ideal for locking sliding plates, clamps and bars. Supplied as pack of 4. Dimensions : Thread - M6 Diameter - 32mm Height - 15mm Thread length - 20mm Please note...

8.49 £
Made from reinforced plastic with lift and lock ratchet system. With steel tapped insert. Suitable when lever turning angle is limited. Supplied as pack of 1. Dimensions : Thread - M10 Diameter - 80mm Height - 45mm Plea...

17.70 £
Made from re-inforced plastic, with a plated steel studding. Ideal for locking sliding plates, clamps and bars. Supplied as pack of 4. Dimensions : Thread - M8 Diameter - 40mm Height - 17mm Thread length - 25mm Please note...

11.49 £
Made from reinforced plastic with lift and lock ratchet system. With steel tapped insert. Suitable when lever turning angle is limited. Supplied as pack of 1. Dimensions : Thread - M12 Diameter - 100mm Height - 65mm Ple...

18.34 £
Made from re-inforced plastic, a brass insert. Ideal for locking sliding plates, clamps and bars. Supplied as pack of 4. Dimensions : Thread - M8 Diameter - 40mm Height - 17mm Please note that prices in the Trend Catalogue...

5.49 £
Made from re-inforced plastic, with a plated steel studding. Suitable when a strong clamping action is required. Supplied as pack of 2. Dimensions : Thread - M6 Diameter - 32mm Height - 23mm Thread length - 20mm Please not...

8.49 £
Made from re-inforced plastic, with a plated steel studding. Suitable when a strong clamping action is required. Supplied as pack of 2. Dimensions : Thread - M10 Diameter - 50mm Height - 32mm Thread length - 40mm Please no...