Here are the Top Ten rules to make your electric fence work properly!1 Keep your fence as free from growth as possible – Growth impairs the output of every commercial appliance and results in increased power consumption, especially with battery-driven appliances.2 Make sure that the earthing is optimal.3 Do not connect two conductive plastic wires by tying them – Use special conductors.4 Fence wire/tape/rope must not be broken.5 Use conductive material having the best possible conductivity – i.e. Low resistance.6 Keep fence wire and earthing rod free from rust – Rust is an insulator.7 Weather-beaten or nagged insulators are unsuitable – Causes a high loss of output.8 Ensure connection between the energiser and wire is optimal – Use cable resistant to high voltage for underground feeds.9 With battery-driven energisers, check battery condition regularly.10 Ensure that each point of the fence is live using an electric fence tester.This DP350B energiser can provide output for up to 600 metres of single strand fencing using four D-cell batteries (6v) and up to 1200 metres using a 12v wet cell battery. Suitable for strip grazing or small paddocks.Contents* DP350B energiser* 4 D-cell back-up batteries, integral earth stake/ stand and connections for both battery typesFeatures* Instant power* Adjustable pulse rate from 20 – 60 pulses per minute to increase battery life.* 2 years warrantySee item code 41331 for replacement D-cell batteries.If only D-cell batteries are used for a short period an economy tester will not detect the pulse and a five light fence tester will be required. The D-cell battery option is best considered as 'back-up' or for use on a short temporary fence. The fencer gives a higher output with a 12v wet cell car or leisure battery that are readily available and can be re-charged.For more powerfull alternatives see our CP450 , code 41345 or CP1900 energiser, code: 41350.

Fenceman Tape Connector Pack 5.

Suitable for long fences. Has reinforced edges. 40 mm Tape has 4. x 0.3 mm SS conductors + 9 x 0.2 mm SS Conductors + 2 x 0.25 Copper conductors. Resistance 0.15 Ohm / m. UV protectected. BS230kg.40mm x 200m.

Suitable for long fences. Has reinforced edges. 40 mm Tape has 4. x 0.3 mm SS conductors + 9 x 0.2 mm SS Conductors + 2 x 0.25 Copper conductors. Resistance 0.15 Ohm / m. UV protectected. BS230kg.20mm x 200m

The copper conductors reduce the resistance in the tape and so can increase the life of your battery between charges or allow you to run a longer fence.12.5mm x 200m.Reinforced edges.12.5 mm Tape has 5. x 0.2 mm SS conductors + 2 x 0.25 Copper conductors. Resistance 0.27 Ohm / m. UV protected. Breaking Strain 95kg.

This is a pack of 10 electric fencing posts. The foot support makes them easy to erect and tread into the ground with a good length ground spike to make secure. Available in two heights, 87.5cm and 132cm tall (above ground). Ideal for horse paddocks. The plastic posts are fully insulated to prevent electrical discharge. All plastic fence posts have a mixture of wire, rope and tape slots which are positioned on the posts to allow different heights of tape. These particular posts have 5 insulators for 20mm tape or rope, 3 insulators for 40mm tape. When positioning your fence posts it is recommended that they are between 5 metres and 7 metres apart. If the area is sheltered or the fence tapes are more highly tensioned the distance between posts can be extended, but in areas of rough terrain or wind the electric posts should be closer together. The more tension on the fence tapes, the bigger the distance you can have between posts.These posts can be used with all standard tapes, wires and ropes.* Insulated plastic posts* 10 fencing posts, 87.5cm or 132cm (above ground)* Foot support* Good length ground spike* 5 insulators for 20mm tape or rope* 3 insulators for 40mm tapeWhy Electric Fencing?Whether you want to limit the amount of grazing on offer to your horse, separate certain horses from others, or improve the quality of your paddock by strip grazing – temporary electric fencing is the answer. Many people who haven’t used electric fencing before are worried that it’s dangerous and will hurt their horse or pony when they come into contact with it. However, if you touch an electric fence, the shock you receive is similar to the static you sometimes feel when you touch a car door. It’s simply a psychological barrier and as horses are intelligent animals they soon learn to steer clear. Horses chew on post and rail fences; use them as scratching posts and lean right over them to get at the grass in neighbouring fields. Once again, electric fencing can help sort this problem. Simply screw in extending insulators to the fence posts, which will offset either polywire or electric rope approximately 5cm to 15cm away from the fence. Add an energizer and your fence is protected. The same solution can be used to keep horses away from barbed wire fences.Here are the Top Ten rules to make your electric fence work properly!1 Keep your fence as free from growth as possible – Growth impairs the output of every commercial appliance and results in increased power consumption, especially with battery-driven appliances.2 Make sure that the earthing is optimal.3 Do not connect two conductive plastic wires by tying them – Use special conductors.4 Fence wire/tape/rope must not be broken.5 Use conductive material having the best possible conductivity – i.e. Low resistance.6 Keep fence wire and earthing rod free from rust – Rust is an insulator.7 Weather-beaten or nagged insulators are unsuitable – Causes a high loss of output.8 Ensure connection between the energiser and wire is optimal – Use cable resistant to high voltage for underground feeds.9 With battery-driven energisers, check battery condition regularly.10 Ensure that each point of the fence is live using an electric fence tester.

Pack of 10 postsHeight above ground 90cmLength of spike 20cm40mm tape holders at 10cm, 46cm 61cm and 81cm from ground20mm tape holders at 19cm and 28cm from ground.Earth lead clip included in foot.

Insulated testing meter with lights, just clip the tester onto tape or wire and push probe into ground.

To connect energisers to fence lines

This universal reel is designed for tape, rope and polywire. Made from tough plastic for durability. The tape reel will carry up to 100 metres of 40mm tape and has a small side winding handle. There is a solid ergonomic handle enabling a firm grip when winding. Situated just above the handle are two hooks which allow the reel to hang from a wire or post hook. Releasing the centre pin spring clip allows the tape reel to slide off leaving a rod that will go through the centre of a polywire reel that will take up to 1000 metres. Makes for ease of playing out or winding up tapes and wires. Keeping fencing tape stored on a reel will ultimately prolong the condition and life of the tape.* Tape winding reel* 1000 metres of polywire* 100 metres of 40mm tape* Tough plastic* Detachable drum* Ergonomic handle* Small drum winding handle* Hooks for fence hangingHere are the Top Ten rules to make your electric fence work properly!1 Keep your fence as free from growth as possible – Growth impairs the output of every commercial appliance and results in increased power consumption, especially with battery-driven appliances.2 Make sure that the earthing is optimal.3 Do not connect two conductive plastic wires by tying them – Use special conductors.4 Fence wire/tape/rope must not be broken.5 Use conductive material having the best possible conductivity – i.e. Low resistance.6 Keep fence wire and earthing rod free from rust – Rust is an insulator.7 Weather-beaten or nagged insulators are unsuitable – Causes a high loss of output.8 Ensure connection between the energiser and wire is optimal – Use cable resistant to high voltage for underground feeds.9 With battery-driven energisers, check battery condition regularly.10 Ensure that each point of the fence is live using an electric fence tester.

Polywire is ideal for using on top of existing wooden post and rail fences to prevent horses from chewing on posts or leaning over in to the next field. Also to keep horses from barbed wire fences. This fencing wire is flexible and light and has 3 stainless steel strand conductors running through its length to ensure good conductivity. Rated at 15 Ohms/metre. 40Kgs breaking strength. A choice of 250 or 500 metres on a reel. Green/white colour with UV protection.* Plastic* 3 stainless steel strand conductors* 15 Ohms/Metre* 40kgs breaking strength* Flexible* Light* Good conductivity* 250 or 500 metres on a reel* UV protection* Green/whiteHere are the Top Ten rules to make your electric fence work properly!1 Keep your fence as free from growth as possible – Growth impairs the output of every commercial appliance and results in increased power consumption, especially with battery-driven appliances.2 Make sure that the earthing is optimal.3 Do not connect two conductive plastic wires by tying them – Use special conductors.4 Fence wire/tape/rope must not be broken.5 Use conductive material having the best possible conductivity – i.e. Low resistance.6 Keep fence wire and earthing rod free from rust – Rust is an insulator.7 Weather-beaten or nagged insulators are unsuitable – Causes a high loss of output.8 Ensure connection between the energiser and wire is optimal – Use cable resistant to high voltage for underground feeds.9 With battery-driven energisers, check battery condition regularly.10 Ensure that each point of the fence is live using an electric fence tester.

This electric fencing line tester could not be simpler to use. Push the earth prong into the ground and then touch the tester wire to the fencing tape. The bulb will light up to indicate the fence is `live'. Unit also has a test button. Size 85mm x 20mm.* Simple and easy to use* Earth prong* `Live' indicator bulb* Test buttonHere are the Top Ten rules to make your electric fence work properly!1 Keep your fence as free from growth as possible – Growth impairs the output of every commercial appliance and results in increased power consumption, especially with battery-driven appliances.2 Make sure that the earthing is optimal.3 Do not connect two conductive plastic wires by tying them – Use special conductors.4 Fence wire/tape/rope must not be broken.5 Use conductive material having the best possible conductivity – i.e. Low resistance.6 Keep fence wire and earthing rod free from rust – Rust is an insulator.7 Weather-beaten or nagged insulators are unsuitable – Causes a high loss of output.8 Ensure connection between the energiser and wire is optimal – Use cable resistant to high voltage for underground feeds.9 With battery-driven energisers, check battery condition regularly.10 Ensure that each point of the fence is live using an electric fence tester.

The extended insulator is for up to 40mm tape and also takes rope or twine. The rope hole gives a 22cm offset from the post, keeping the animal off the fencing. Perfect for fastening to wooden posts as it has a unique screw thread that helps avoid wood split. * Pack of 10 * Plastic with metal screw* 22cm offset from post* Up to 40mm fencing tape, rope or twine* Black* Screw into wooden posts* Full insulationHere are the Top Ten rules to make your electric fence work properly!1 Keep your fence as free from growth as possible – Growth impairs the output of every commercial appliance and results in increased power consumption, especially with battery-driven appliances.2 Make sure that the earthing is optimal.3 Do not connect two conductive plastic wires by tying them – Use special conductors.4 Fence wire/tape/rope must not be broken.5 Use conductive material having the best possible conductivity – i.e. Low resistance.6 Keep fence wire and earthing rod free from rust – Rust is an insulator.7 Weather-beaten or nagged insulators are unsuitable – Causes a high loss of output.8 Ensure connection between the energiser and wire is optimal – Use cable resistant to high voltage for underground feeds.9 With battery-driven energisers, check battery condition regularly.10 Ensure that each point of the fence is live using an electric fence tester.

This is a quality standard fencing tape. It has 10 strand, 0.16mm stainless steel conductors running through its 40mm width. There is 200 metres of tape on the reel, which will cross 28 fence posts, in single strand, at seven metres apart in good fencing areas. A feature of this fence tape is that it has UV protection to stop the tape degenerating in strong sunlight. Good width tape offering good coverage for a good price!* 40mm width tape* 200 metres reel length* 10 strand, 0.16mm stainless-steel conductors* UV protection* White colourHere are the Top Ten rules to make your electric fence work properly!1 Keep your fence as free from growth as possible – Growth impairs the output of every commercial appliance and results in increased power consumption, especially with battery-driven appliances.2 Make sure that the earthing is optimal.3 Do not connect two conductive plastic wires by tying them – Use special conductors.4 Fence wire/tape/rope must not be broken.5 Use conductive material having the best possible conductivity – i.e. Low resistance.6 Keep fence wire and earthing rod free from rust – Rust is an insulator.7 Weather-beaten or nagged insulators are unsuitable – Causes a high loss of output.8 Ensure connection between the energiser and wire is optimal – Use cable resistant to high voltage for underground feeds.9 With battery-driven energisers, check battery condition regularly.10 Ensure that each point of the fence is live using an electric fence tester.

Takes up to 40mm tape.

For all tape upto 20mm

This is a replacement or spare fencer energiser battery. 75 amp / 9 volts / 90 Ah. Sealed and compact. Small disposal weight. High efficiency also at 6° C. Not rechargeable. Alkaline version of 90Ah saline battery. Energy output 570 Wh. Suitable for fencers up to 0.8J.* Not rechargeable* Dry battery* Sealed and compact* Ag-fence* 9 volt / 90Ah / 75 amp* Energy output 570 Wh* Alkaline version of 90Ah saline battery* High efficiency also at 6° C* Suitable for small fencers – up to 0.8J. If you require power for your fencing our range of energisers provide ample coverage and simplicity of operation.For battery energisers see:CP250 constant power energiser, code: 41307CP500 constant power energiser, code: 41307DP350B battery energiser, code: 41330.Here are the Top Ten rules to make your electric fence work properly!1 Keep your fence as free from growth as possible – Growth impairs the output of every commercial appliance and results in increased power consumption, especially with battery-driven appliances.2 Make sure that the earthing is optimal.3 Do not connect two conductive plastic wires by tying them – Use special conductors.4 Fence wire/tape/rope must not be broken.5 Use conductive material having the best possible conductivity – i.e. Low resistance.6 Keep fence wire and earthing rod free from rust – Rust is an insulator.7 Weather-beaten or nagged insulators are unsuitable – Causes a high loss of output.8 Ensure connection between the energiser and wire is optimal – Use cable resistant to high voltage for underground feeds.9 With battery-driven energisers, check battery condition regularly.10 Ensure that each point of the fence is live using an electric fence tester.

This 240 plug transformer can be used to convert your CP900 or CP1900 to mains power.For Indoor use only.

CP900 12V 09J BATTERY & MAINS ENERGIZER • Electrifies up to 7km of fence with light vegetation • Suitable for all round farm use • Powered by external 12 battery (not supplied) or 4 D cell batteries (supplied) or mains power via mains adaptor ( must be housed in a dry building) • Constant Power output • Fast or energy conserving slow pulse rate • High Power 086J • Low Power 043J • Output LED indicator • LED and bleep warning if fence voltage under 2000v • 3 stage battery low warning LED • Uninterruptable power when connected to the mains and using 12v back up battery • Day mode High power day, Low power night. • Night mode High power night, Low power day • Complete with earth stake and leads • 3 years warranty

CP1900 12V BATTERY & MAINS ENERGIZER•Electrifies up to 14km of fence with light vegetation•Suitable for all round farm use•Powered by external 12 battery (not supplied) or 4 D cell batteries (supplied) or mains power via mains adaptor ( must be housed in a dry building)•Constant power output.•Fast or energy conserving slow pulse rate.•High Power 1.86J•Low Power 1.04J•Output LED indicator.•LED and bleep warning if fence voltage below 2000v•3 stage battery low warning LED.•Uninterruptable power when connected to the mains and using a 12v back up battery.•Day mode High Power day, Low power night.•Night mode High power night, Low power day•Complete with earth stake and leads•3 years warranty