An extra shallow profiler for trimming an edge to a template. For use when making templates from 3 - 4mm MDF or plywood. Shallow cut length makes profiling easier as a thicker false top is not required and a thinner template can be used. Di...

Thumb knob spring for the T10 router. Please note that prices in the Trend Catalogue download, if shown below, may differ to the website prices, as those listed in the Catalogue are Trend List Prices excluding VAT....

Power socket for the T11ELK router. Dimensions : 115 VOLT Please note that prices in the Trend Catalogue download, if shown below, may differ to the website prices, as those listed in the Catalogue are Trend List Prices excluding VAT....

Designed to accommodate the Schlegel Aquamac 63 weather strip system. Allows for a particularly small gap between sash and frame. The slot can be positioned part way down the side of the rebate, or at the bottom of the rebate. The Recessin...

Two fluted Solid Carbide insert straight cutters. Suitable for a wide range of applications such as engraving, grooving, rebating and shallow mortising. Use on softwoods, hardwoods, MDF, plywood and chipboard. Has a bottom cut feature.

Attractive edge moulds. A full corner bead can be produced by making a second pass at 90 degrees. Dimensions : Diameter=31.9 mm Cutting Radius 1 : 7 mm Shank Diameter : 1/4 inch Please note that prices in the Trend Catalogue d...

Two fluted Solid Carbide insert straight cutters. Suitable for a wide range of applications such as engraving, grooving, rebating and shallow mortising. Use on softwoods, hardwoods, MDF, plywood and chipboard. Has a bottom cut feature.

Can be used with radius cutters, to make rule joints. Dimensions : Diameter=38 mm Cutting Length : 18 mm Cutting Radius : 12.7 mm Shank Diameter : 1/2 inch Please note that prices in the Trend Catalogue download, if shown below,...

Switch for the T10 router. Please note that prices in the Trend Catalogue download, if shown below, may differ to the website prices, as those listed in the Catalogue are Trend List Prices excluding VAT....

For use in a router table only. Take 3 - 4 passes at repeated depths. Can be used for curved panels if a copy pin is used. Dimensions : Diameter=41 mm D2=7 mm Cutting Length : 9/32 inch Cutting Length : 7 mm Cutting Radius ...

A two flute 22.5 degree bevel cutter for routing eight sided stave box. Dimensions : Diameter=28 mm D2=4.82 mm Cutting Length : 28 mm Overall Length : 68 mm Angle : 67.5 degrees Shank Diameter : 1/4 inch Please note that pr...

Replacement bearing for router cutter. Always check the tightness of the fixing screw before using the cutter. Ball bearings should be wiped clean, not dipped in solvent. Prevent resin build-up by cleaning with wire brush. Dimensions : ...

TCT for abrasive materials such as chipboard, MDF, plywood and certain hardwoods. Two flutes for clean finish. Suitable for plunge routers. TCT centre tip. Dimensions : Diameter=15 mm Cutting Length : 35 mm Overall Length : 76 ...

This Profile Scriber produces the same type of joint, and use the same components as the standard PSC sets. Both parts of the joint are cut by only changing the cutter height. No reassembly of parts is required, to convert the tool from scribin...

This Profile Scriber produces the same type of joint, and use the same components as the standard PSC sets. Both parts of the joint are cut by only changing the cutter height. No reassembly of parts is required, to convert the tool from scribin...

For use with commercial dovetailing and stair-housing jigs. The cutter will produce sliding and lapped dovetails, through dovetails and end on dovetails. Purpose made for stair housing jigs. Left hand. Dimensions : Diameter=19 mm

For stationary machines or portable routers mounted in a table. Fixed head use, maximum 18000 rpm. Dimensions : Diameter=50 mm Cutting Radius 1 : 12 mm Shank Diameter : 12 mm Please note that prices in the Trend Catalogue downl...

Two fluted Tungsten Carbide Tipped straight cutters. Suitable for a wide range of applications such as engraving, grooving, rebating and shallow mortising. Use on softwoods, hardwoods, MDF, plywood and chipboard. Has a bottom cut feature....

Replacement collet nut for the T2. Dimensions : Collet nut to suit Trend T2 Please note that prices in the Trend Catalogue download, if shown below, may differ to the website prices, as those listed in the Catalogue are Trend List Pri...

A horizontal pressure guard for the Craftsman Router Table, for holding narrow work against the fence face. Consisting of two spring steel fingers fitted to a baseplate, it is adjusted and secured by captive threaded studs fitted through the exist...