A portable two piece template set for easy handling designed for recessing hinges in wooden doors and frames. It has been designed for ease of use and to minimise setting-up time. Use on-site and in joinery shops to increase productivity. N...

Additional mortise template for the LOCK/JIG. Dimensions : 42X75/37X59mm Please note that prices in the Trend Catalogue download, if shown below, may differ to the website prices, as those listed in the Catalogue are Trend List Prices...

For coves and part of a rule joint. Single flute. Dimensions : Diameter=12.7 mm Cutting Length : 19 mm Overall Length : 64 mm Cutting Radius 1 : 6.3 mm Shank Diameter : 1/2 Please note that prices in the Trend Catalogue do...

Self-guiding chamfer/bevel cutter. Bearing follows the board beneath. Dimensions : Diameter=51 mm Angle : 45 degrees Shank Diameter : 1/2 inch Please note that prices in the Trend Catalogue download, if shown below, may differ ...

Cutter for trimming and bevelling timber, lippings and plastic laminate edges or any shaping applications. Self-guiding trimmer with bearings mounted on end of cutter. For trimming plastic or plywood overlay. For copy profiling, use the bea...

Pair of sliding friction clamps for the VARIJIG. Please note that prices in the Trend Catalogue download, if shown below, may differ to the website prices, as those listed in the Catalogue are Trend List Prices excluding VAT....

Two fluted Solid Carbide insert straight cutters. Suitable for a wide range of applications such as engraving, grooving, rebating and shallow mortising. Use on softwoods, hardwoods, MDF, plywood and chipboard. Has a bottom cut feature.

6mm collet for the T2K. Dimensions : Split sprung 6mm Please note that prices in the Trend Catalogue download, if shown below, may differ to the website prices, as those listed in the Catalogue are Trend List Prices excluding VAT....

1/4 inch collet for the T2K. Dimensions : Split sprung 1/4 inch Please note that prices in the Trend Catalogue download, if shown below, may differ to the website prices, as those listed in the Catalogue are Trend List Prices excludin...

Protected in a plastic carrying case, this twelve piece set contains a range of the most widely used cutters for both decorative as well as constructional woodworking. The set contains two straight cutters, a radius cove, a V groove and a dovetail...

Two flute tungsten carbide tipped dovetail cutter for use with the DC400 dovetailing centres. Dimensions : Diameter : 11.3mm Cutting Length : 7.5mm Angle : 20 degrees Shank Diameter : 8mm Shank Length=45mm Please note that pri...

An accurate and easy to use Craft Range dovetail jig for a variety of elegant dovetail joints. Cuts 1/2 inch wide half blind dovetails or rebated dovetails in one operation. The jig has adjustable offset stops. Dimensions : Material thick...

Use for bevelling, chamfering and for producing mortar grooves. Approx. 1.0mm flat will be found on nose. Dimensions : Diameter : 38mm Cutting Length 1 : 19mm Cutting Length 2 : 26.5mm Angle : 45 degrees Shank Diameter : 1/2 inch

Especially designed bevel cutter for routing Corian, which is used in many bathrooms and kitchens. Dimensions : Diameter : 23mm Cutting Length : 25mm Shank Diameter : 3/8 inch Please note that prices in the Trend Catalogue downloa...

Two flute straight cutter with 3 degree taper. Designed for constructing wooden vacuum forming moulds. Tapered sides will allow the mould to release easily. Dimensions : Diameter : 12.7mm Cutting Length : 32mm Overall Length : 80m...

Trend Chamfer 'V' Groove A=45í X 18mm (Tct Router Cutter Range / Chamfer) Use for bevelling, chamfering and for producing mortar grooves. Approx. 1.0mm flat will be found on nose. Ideal for imitating 'V' jointed tongue and groove on man-...

Trend Chamfer 'V' Groove A=60í 257084 (Tct Router Cutter Range / Chamfer) Use for bevelling, chamfering and for producing mortar grooves. Approx. 1.0mm flat will be found on nose. Dimensions : Diameter : 12.7mm Cutting Length 1 : ...

This machine bit is designed for recessing circular concealed hinges. The shank has a flat for securing and a grub screw for height adjustment. Use at recommended speeds of 6000RPM. Dimensions : Diameter : 30mm Overall Length : 57mm

This machine bit is designed for recessing circular concealed hinges. The shank has a flat for securing and a grub screw for height adjustment. Use at recommended speeds of 6000RPM. Dimensions : Diameter : 35mm Overall Length : 57mm

For coves and part of a rule joint. Solid Carbide insert. Dimensions : Diameter : 1/8 inch Diameter : 3.2 mm Cutting Length : 3/8 inch Cutting Length : 9.5 mm Shank Diameter : 1/4 inch Please note that prices in the Trend C...