Replacement bearing for router cutter. Always check the tightness of the fixing screw before using the cutter. Ball bearings should be wiped clean, not dipped in solvent. Prevent resin build-up by cleaning with wire brush. Dimensions : ...

Bearing for slotting systems. Ball bearings should be wiped clean, not dipped in solvent. Prevent resin build-up by cleaning with wire brush. Dimensions : IDiameter : 12.0mm ODiameter : 29.0mm Thickness=5.9mm Please note tha...

Replacement bearing for router cutter. Always check the tightness of the fixing screw before using the cutter. Ball bearings should be wiped clean, not dipped in solvent. Prevent resin build-up by cleaning with wire brush. With the design...

Alternate bearing ring for the 46/390X1/2TC, giving a rebate size of 18.25mm. The bearing ring is secured to the cutter by fitting the ball bearing either side and tightening the screw. Dimensions : IDiameter : 12.7mm ODiameter : 14.3mm Reb...

Alternate bearing ring for the 46/390X1/2TC, giving a rebate size of 15.9mm. The bearing ring is secured to the cutter by fitting the ball bearing either side and tightening the screw. Dimensions : IDiameter : 12.7mm ODiameter : 19.1mm Reba...

Two fluted Solid Carbide insert straight cutters. Suitable for a wide range of applications such as engraving, grooving, rebating and shallow mortising. Use on softwoods, hardwoods, MDF, plywood and chipboard. Has a bottom cut feature.

Two fluted Tungsten Carbide Tipped straight cutters. Suitable for a wide range of applications such as engraving, grooving, rebating and shallow mortising. Use on softwoods, hardwoods, MDF, plywood and chipboard. Has a bottom cut feature....

Two fluted Tungsten Carbide Tipped straight cutters. Suitable for a wide range of applications such as engraving, grooving, rebating and shallow mortising. Use on softwoods, hardwoods, MDF, plywood and chipboard. Has a bottom cut feature....

Two fluted Tungsten Carbide Tipped straight cutters. Suitable for a wide range of applications such as engraving, grooving, rebating and shallow mortising. Use on softwoods, hardwoods, MDF, plywood and chipboard. Has a bottom cut feature....

Single fluted Tungsten Carbide straight cutter for fast free cutting. This cutters has extra clearance and gives a stronger backing support to the tip. Single flute should be chosen where speed and clearance rates are more important than the f...

Single fluted Tungsten Carbide straight cutter for fast free cutting. This cutters has extra clearance and gives a stronger backing support to the tip. Single flute should be chosen where speed and clearance rates are more important than the f...

This dovetail cutter produces a tight reliable joint for drawers, boxes etc. Solid Carbide Insert. Dimensions : Diameter : 12.7mm Cutting Length : 12.7mm Overall Length : 61mm Angle : 104 degrees Shank Diameter : 1/4 inch Pl...

For veining, panelling, 'V' grooving, bevelling & chamfering. Dimensions : Diameter : 12.7mm Cutting Length : 6mm Angle : 45 degrees Shank Diameter : 8mm Please note that prices in the Trend Catalogue download, if shown below, ma...

Self-guiding chamfer/bevel cutter. Bearing follows the board beneath. Dimensions : Cutting Length : 12.7mm Bearing Diameter : 9.5mm Angle : 45 degrees Shank Diameter : 1/4 inch Please note that prices in the Trend Catalogue do...

This cove style cutter with two flutes, give radiused grooves for decorative panel finishes and board edges. For deep channels, take a series of passes. Dimensions : Diameter : 15.9mm Cutting Length : 9.5mm Cutting Radius : 7.9mm Sh...

Ideally suited for cutting radiused edges at speed, as a side fence can be dispensed with. The guide bearing follows the vertical edge or template. Dimensions : Cutting Length : 14.3mm Bearing Diameter : 9.5mm Cutting Radius : 4.8mm

Ideally suited for cutting radiused edges at speed, as a side fence can be dispensed with. The guide bearing follows the vertical edge or template. Dimensions : Cutting Length : 14.3mm Bearing Diameter : 9.5mm Cutting Radius : 6.3mm

Ideally suited for cutting radiused edges at speed, as a side fence can be dispensed with. The guide bearing follows the vertical edge or template. Dimensions : Cutting Length : 14.3mm Bearing Diameter : 9.5mm Cutting Radius : 7.9mm

Ideally suited for cutting radiused edges at speed, as a side fence can be dispensed with. The guide bearing follows the vertical edge or template. Dimensions : Cutting Length : 19.1mm Bearing Diameter : 9.5mm Cutting Radius : 12.7mm

This staff bead is ideal for producing nosings and attractive edges. Edge cut only. Dimensions : Cutting Length : 12.7mm Cutting Radius : 2mm Shank Diameter : 1/4 inch Please note that prices in the Trend Catalogue download, if ...