This plug cutter produces plugs to exactly fit counterbored holes produced by Ref. 62 & 63 group tools. Use at recommended speeds of 1000-20000RPM. Dimensions : Diameter : 16mm Cutting Length : 16mm Shank Diameter : 1/4 inch Ple...

Making holes in wood and other soft materials is twice as fast with the 3D-Bit. You will notice the difference immediately if you compare it with normal drills. Unlike any other drills, the 3D-Bit has sharp cutting edges in three directions.

Has 2 lips, 2spurs and a centre brad point. Flutings are backed-off to give a radial relief and assist chip clearance. This drill is used mainly for drilling cross grained timber and particle board. Used in all branches of industry when clea...

Has 2 lips, 2spurs and a centre brad point. Flutings are backed-off to give a radial relief and assist chip clearance. This drill is used mainly for drilling cross grained timber and particle board. Used in all branches of industry when clea...

Has 2 lips, 2spurs and a centre brad point. Flutings are backed-off to give a radial relief and assist chip clearance. This drill is used mainly for drilling cross grained timber and particle board. Used in all branches of industry when clea...

This machine bit is typically used by kitchen furniture manufacturers for recessing circular hinges. Without scribers are for laminate covered boards. Dimensions : Diameter : 15mm Overall Length : 60mm Shank Diameter : 1/4 inch ...

This machine bit is typically used by kitchen furniture manufacturers for recessing circular hinges. Without scribers are for laminate covered boards. Use at speed range 2000 -12000RPM to avoid burning. Use with pillar drills only. Di...

This 60 degree taper multi-boring drill is ideal for end grain and through hole drilling applications. Reduces the likelihood of +break out+ to a minimum. Drill has a Solid Carbide cutting tip. Shank has one flat for positive holding. A t...

This 60 degree taper multi-boring drill is ideal for end grain and through hole drilling applications. Reduces the likelihood of +break out+ to a minimum. Drill has a Solid Carbide cutting tip. Shank has one flat for positive holding. A t...

This countersink is produced from the best grade carbon steel, leaves a clean cut finish by virtue of their multi-tooth deep ground gullets. For use with fast spiral drills. Fits metric drills from 3mm to 12mm inclusive. Drill bit not includ...

Designed to drill and countersink simultaneously, a wide variety of materials. Supplied complete with HSS twist drill. Fully adjustable, a hex key is supplied. When setting-up, ensure flutes of drill are aligned with flute of counterbore.

Made from Carbon steel and precision machined. Has a spiral point, single flute. Ideal for quick, clean deep holes. Must only be used with torque control drills to prevent wrist injury. Dimensions : Diameter : 16mm Overall Length : 155mm...

Made from Carbon steel and precision machined. Has a spiral point, single flute. Ideal for quick, clean deep holes. Must only be used with torque control drills to prevent wrist injury. Dimensions : Diameter : 12mm Overall Length : 155mm...

An economical bit for cutting quick holes in timber. With centre point, back tapered cutting edge and ground chip breakers. Dimensions : Diameter : 18mm Overall Length : 152mm Shank Diameter : 1/4 inch Hex Please note that price...

An economical bit for cutting quick holes in timber. With centre point, back tapered cutting edge and ground chip breakers. Dimensions : Diameter : 28mm Overall Length : 152mm Shank Diameter : 1/4 inch Hex Please note that price...

An economical bit for cutting quick holes in timber. With centre point, back tapered cutting edge and ground chip breakers. Dimensions : Diameter : 8mm Overall Length : 152mm Shank Diameter : 1/4 inch Hex Please note that prices...

TCT hinge sinking cutter for pillar drills only. Designed for recessing holes in melamine covered chipboard to receive circular hinges. For drilling machines Dimensions : Diameter : 25 mm Shank Diameter : 8mm Please note that p...

TCT hinge sinking cutter for pillar drills only. Designed for recessing holes in melamine covered chipboard to receive circular hinges. For drilling machines Dimensions : Diameter : 30 mm Shank Diameter : 8mm Please note that p...

Features & Benefits : &bull 4, 6, 8, 10, 12mm &bull Ideal solution for drilling hard tiles &bull Rubber suction cup for instant positioning &bull Individual slots for the most popular fixing sizes Use in conjunction wi...

Features & Benefits : &bull Diamond grit edged bit, ideal for drilling hard tiles &bull Slotted bit design for easy waste removal &bull Suitable for use with most power drills &bull Cuts porcelain, granite, quarry, stone, marble...