TCT cutter with staggered cutting surfaces. Deep mortising and grooving giving good chip clearance. For lock mortising, two width cuts will be needed to achieve the standard 19mm mortise. Will plunge and clear chips to a depth of 70mm in a n...

A large ogee panel mould cutter for traditional panelled doors. For stationary machines or portable routers mounted in a table at 12000 RPM recommended speed. Dimensions : Diameter=86 mm Cutting Radius : 22 mm Shank Diameter : 1/2 in...

Neatly cuts grooves on doors or frames to accept Intumescent Strip. By using alternative ball bearing diameters, other seal thicknesses can be introduced. For either frame or door applications, with standard or Smokeseal Intumescent Strip. A...

All in one work top jig for up to 900mm worktops, for use by tradesmen. Will cut left hand and right hand corners, R400mm peninsular joint, 45degree end cut with slight radius, 22.5degree -trade+ corner solution, R100mm radius corner, R40mm radius co...

This Raised Panel cutter runs best at lower speeds between 12,000 and 18,000 RPM. Matches our range of profile scribers. Suitable for use on natural timber and MDF. When joining sections to produce solid wood panels, alternate the growth r...

Attractive edge moulds. A full corner bead can be produced by making a second pass at 90 degrees. Dimensions : Diameter=31.9 mm Cutting Radius 1 : 7 mm Shank Diameter : 1/2 inch Please note that prices in the Trend Catalogue d...

Two fluted Solid Carbide insert straight cutters. Suitable for a wide range of applications such as engraving, grooving, rebating and shallow mortising. Use on softwoods, hardwoods, MDF, plywood and chipboard. Has a bottom cut feature.

For stationary machines or portable routers mounted in a table at 24000 RPM recommended speed Dimensions : Diameter=41 mm Angle : 10 degrees Shank Diameter : 8mm Please note that prices in the Trend Catalogue download, if shown be...

A reversible finger joint. Max Thickness 18mm. For use on natural timbers and man-made boards. Dimensions : Diameter=40mm Diameter : 31mm Cutting Length : 32mm Shank Diameter : 1/2 inch Please note that prices in the Trend...

Two fluted Tungsten Carbide Tipped straight cutters. Suitable for a wide range of applications such as engraving, grooving, rebating and shallow mortising. Use on softwoods, hardwoods, MDF, plywood and chipboard. Has a bottom cut feature....

Two fluted Solid Carbide insert straight cutters. Suitable for a wide range of applications such as engraving, grooving, rebating and shallow mortising. Use on softwoods, hardwoods, MDF, plywood and chipboard. Has a bottom cut feature.

TCT for abrasive materials such as chipboard, MDF, plywood and certain hardwoods. Two flutes for clean finish. Suitable for plunge routers. Dimensions : Diameter : 7.9mm Cutting Length : 26mm Shank Diameter : 1/4 inch Shank Leng...

TCT for abrasive materials such as chipboard, MDF, plywood and certain hardwoods. Two flutes for clean finish. Suitable for plunge routers. Dimensions : Diameter : 8.1mm Cutting Length : 26mm Shank Diameter : 1/4 inch Please...

TCT for abrasive materials such as chipboard, MDF, plywood and certain hardwoods. Two flutes for clean finish. Suitable for plunge routers. Dimensions : Diameter : 8.9mm Cutting Length : 26mm Shank Diameter : 1/4 inch Please...

Trend B'Guided Ovolo 9.5mm Rad 3.2mm Step (Tct Router Cutter Range / Large Step Round Over & Ovolo) A bearing guided round over & ovolo router cutter supplied with three ball bearings to give a rounding over and two sizes of step ovolo mould o...

Trend B'Guided Ovolo 15.9mm Rad 3.2mm Ste (Tct Router Cutter Range / Large Step Round Over & Ovolo) A bearing guided round over & ovolo router cutter supplied with three ball bearings to give a rounding over and two sizes of step ovolo mould o...

A two piece cutter set to create a traditional frame and panelled door using a router in a table. The cutters have extra long 40mm shanks and can be used in natural timber. Supplied in a wooden box with instructions Dimensions : Profil...

Trend Mitre Corner A=135í X 51.3mm Dia (Tct Router Cutter Range / Jointer) This cutter makes a lapped mitre joint. Thickness Min. 15mm -Max. 18mm. For stationary machines at 18000 RPM. Dimensions : Diameter : 51.3mm Diameter : ...

Ideal for fast chamfering. Popular in the sign making trades. Pin diameter 5.5mm. For chamfering edges of plastic material in the sign industry. Dimensions : Cutting Length 1 : 10mm Cutting Length 2 : 14mm Angle : 45 degrees Sha...

Use for bevelling, chamfering and for producing mortar grooves. Approx. 1.0mm flat will be found on nose. Dimensions : Diameter : 21.5mm Cutting Length 1 : 5.5mm Cutting Length 2 : 12mm Angle : 30 degrees Shank Diameter : 1/4 inch ...