TCT for abrasive materials such as chipboard, MDF, plywood and certain hardwoods. Two flutes for clean finish. Suitable for plunge routers. TCT centre tip. Especially suited for drilling, but to detriment of clearance at high feed rates....

One flute. Eccentric single flute cutter. Cutter is chosen for fast free cutting, when cutting speed takes preference over finish. The depth of cut should be a maximum of 1.0mm per pass. Must not be used in eccentric chucks. This cutte...

Cutter supplied with two bearings. Larger bearing removes the quirk producing a round over profile. Dimensions : Diameter : 24.7mm Cutting Length : 12mm Overall Length : 51mm Bearing Diameter : 9.5 &12.7mm Cutting Radius : 6mm ...

Cutter supplied with two bearings. Larger bearing removes the quirk producing a round over profile. For stationary machines - 12000 RPM recommended speed. Dimensions : Diameter : 76.5mm Cutting Length : 38mm Bearing Diameter : 9.5 ...

Ball end spiral router cutter for three-dimensional routing. Gives a superior performance in three- dimensional carving and general engraving The ball ended to allow for 3D- carving, to give clean transition between depths. Two fluted upcut ...

Features 2mm micrograin Tungsten Carbide tips, for cutting the most abrasive materials to give extra long life. Teflon coated, indicated by distinctive black colouring. Can be used on hardwood & softwood, fibreboard, plywood and particle board....

Features 2mm micrograin Tungsten Carbide tips, for cutting the most abrasive materials to give extra long life. Teflon coated, indicated by distinctive black colouring. Can be used on hardwood & softwood, fibreboard, plywood and particle board....

Features 2mm micrograin Tungsten Carbide tips, for cutting the most abrasive materials to give extra long life. Teflon coated, indicated by distinctive black colouring. Can be used on hardwood & softwood, fibreboard, plywood and particle board....

Features 2mm micrograin Tungsten Carbide tips, for cutting the most abrasive materials to give extra long life. Teflon coated, indicated by distinctive black colouring. Can be used on hardwood & softwood, fibreboard, plywood and particle board....

Features 2mm micrograin Tungsten Carbide tips, for cutting the most abrasive materials to give extra long life. Teflon coated, indicated by distinctive black colouring. Can be used on hardwood & softwood, fibreboard, plywood and particle board....

Features 2mm micrograin Tungsten Carbide tips, for cutting the most abrasive materials to give extra long life. Teflon coated, indicated by distinctive black colouring. Can be used on hardwood & softwood, fibreboard, plywood and particle board....

By raising the cutter, the top quirk is removed. Dimensions : Cutting Length : 13.5mm Bearing Diameter : 9.5mm Cutting Radius : 4mm Shank Diameter : 8mm Please note that prices in the Trend Catalogue download, if shown below, may...

Small panelling cutters, popular for decorative cupboard doors and furniture embellishments. Dimensions : Diameter : 1/2 inch Diameter : 12.7mm Cutting Length : 3/8 inch Cutting Length : 9.5mm Cutting Radius : 2mm Shank Diameter : 8...

Cutter supplied with two bearings. Larger bearing removes the quirk producing a round over profile. Dimensions : Diameter : 41.1mm Cutting Length : 20mm Bearing Diameter : 9.5 & 12.7mm Cutting Radius : 14.2mm Shank Diameter : 12mm...

Pack of 500 square drive self tapping wood screws used with the PH/JIG. Dimensions : No 7 x 30mm Please note that prices in the Trend Catalogue download, if shown below, may differ to the website prices, as those listed in the Catalog...

For safety a clear polycarbonate guard that shields the eyes and face from wood chips when used in conjunction with the RTI/PLATE. Dimensions : Diameter 108mm Thickness 1/4 inch Please note that prices in the Trend Catalogue downlo...

Accessory kit for the DC400 dovetailing centre. Set comprises of the waste collector set, cable support, guide finger sets for 9 degrees, 11 degrees, 14 degrees, 20 degrees, housing template and a seven piece cutter set. Dimensions : Cutter ...

A half blind guide set for DC400 dovetailing centre. Dimensions : 5 pieces Please note that prices in the Trend Catalogue download, if shown below, may differ to the website prices, as those listed in the Catalogue are Trend List Pric...

Complete with ten plastic ended panel connectors. For use independently of Postfom Jigs, which have their own multi-slot template. Please note that prices in the Trend Catalogue download, if shown below, may differ to the website prices, as...

Panel bolt connectors to connect worktop joint together. Dimensions : For connecting worktop joints Metal ended Total length - 150mm Pack of 1000 Please note that prices in the Trend Catalogue download, if shown below, may di...